See this page for the BetSize hotkeys:
http://www.stackandtile.com/sat/help/bet-size-hotkeys

For the advanced action checkboxes, I believe these are the settings:

Those coords need to be relative to the "standard_table_width/height" values at the top of the file. See the instructions on the BetSize page

added in v2.86

http://www.stackandtile.com/forum/sh...d=6722#pid6722

http://www.stackandtile.com/sat/

Thanks Greg, missed that page. Everything working now.

Hi, "Tile all table" hotkey doesn't work properly, I had 2 table in the stack, I used the hotkey and only one table was move to the grid

This is the default behavior of that hotkey. It leaves one table in the stack so that the entire grid is full. Usually people use slot1 for their stack, so by keeping a table in the stack, all their slots get filled in order from slot 1-onwards

You can change it by adding a line to your config file. I just added the setting to the bottom of the Extra Advanced Options help page. It was missing previously

http://www.stackandtile.com/sat/help...vanced-options

^ ty

Hello!

Is this software capable to move the seats and the bet sizes/chips to other X-Y coordinates?
I would like to move up and close the villians to have more free space for the hud on both sides. On WP network they are very close to the middle on the sites, and that is a problem for me.
Similar how Imodder can modify the table layout on ipoker.

No, this software does not modify the table graphics. Its purpose is to provide features to allow players to play more tables at the same time without the usual inconveniences

Thy for the reply Greg!
Okay, and do you know any software that can modify the table graphics on WPN?

Or can you give me a hint if its even possible from user's side?

Unfortunately I have no idea about that

I see, thank you btw, have a good night!

Have there been any problems reported with the "new" Ipoker software since the recent Stackandtile update?

Today when my Ipoker table imported into my tiled grid it started to convulse as if it was trying to resize and seized all control of my mouse. I attempted to wait it out and even tried to disconnect my mouse and reconnect it when that failed, attempted shutting down the process of StackandTile in the task manager but unaware how to do so with no control of the mouse so I was forced to leave my session and reboot.

After that I re-configured the Ipoker site thinking maybe that would fix it all seemed well until maybe half an hour later when I think I may have clicked a bit of the edge on the Ipoker's table side and moved it triggering the same convulsions back and forth as explained above with no control of my mouse. So I restarted again and forwent using stackandtile the rest of my session.

Had same problem with Ipoker today. WilliamHill.
But that problem only occurred when HM2 HUD was working. When I turned HM2 off SaT re-sized table normally and I could control my mouse. After that I turned HM2 on again and could play normally.

Also put some hotkey for "Start/Stop SaT". You will not need to restart your PC mid grind if have this problem where SaT tries to re-size table for long time and you can not control mouse.

I got a popup after upgrading to the newest client but didn't read it, I am on the following sites is there anything I need to change before proceeding

Thanks.

you have to remove and re-add the 888 one in StackandTile.

Microsoft Security Essentials detected Malware at the newest update?

This was reported on the SaT forums, and then I put out an update and people said it was fixed. It sounds like Removing and re-Including the site fixed it. But then mid-session you may have accidentally tried to resize the table, and then SaT tried to resize it back. This may end up being a never ending problem with this new iPoker software, unfortunately.


Alternatively, there is a built-in hotkey to auto-quit SaT

CTRL + ALT + SHIFT + Q

http://www.stackandtile.com/sat/help...-switch-hotkey

yep

See here for official response
http://www.stackandtile.com/sat/help...alse-positives

This seems like it happens more frequently each time I put out a new version. As if these AV companies can't get their **** straight and realize its the same program with just some minor updates. I already submitted it to Symantec and they came back saying its a false positive
http://www.stackandtile.com/forum/sh...d.php?tid=1293

What version of Windows are you on? I would appreciate it if you could submit the file to MS for review.

You can submit it to MS here:
https://www.microsoft.com/en-us/secu...on/submit.aspx

Windows 7

Windows 10 here, and when updating SaT I get "StackAndTile_Setupexe contained a virus and was deleted." message. So I cant update. Whats the fix?

Update, immediately after trying to update SaT, I endend up with this "Trojan:Win32/Fethar.A!d" Virus detected by Windows Defender!

Now I'm having a bunch of problems, you might want to check your file before this happens to anyonelse

Please see the few posts above.

I have already submitted the file to MS at the link I provided. But it can only help if more people submit it. So if you could do that as well, I would appreciate it.

Originally someone reported that VirusTotal was showing 4 bad detections:
http://f-picture.net/lfp/s017.radika...4cc2c2.png/htm

I've been submitting the file and now its down to 1:
https://www.virustotal.com/en/file/9...bc34/analysis/

Unfortunately, if these stupid AV companies don't change their detections, then every time I put out an update this will be a problem.