Even though the buttons are blue, the colors fade maybe from light blue to dark blue within the button, and sometimes there are black and browns that makeup that fade. if it works, thats all that really matters.

i'm curious about the stack cycling incorrectly when a table breaks. that shouldnt happen on its own. the stack will cycle through whenever a table that is in grid needs attention. if a table in grid needs attention, and no table in stack does, the stack will keep cycling until a table in stack does need action, or until you act on the table in grid.

try also adding these lines to your SaT-new.ini, and let me know

obviously replace with your pokersite and with your fold coords

The problem seems to have gone away.

However, something else interesting is happening. When I open a FTP Table (in addition to my Stars tables) I put them into the Stack after I buy in (while in the New Slot), and they immediately move to the first available free slot even though they are "waiting for the BB". If I put them back into the stack they immediately return to the first free slot. When I first began adding FTP tables this did not happen, it has only happened during the last 2 sessions.

i assume 'preflop' tile setting

i've had this problem with FTP, but only when i'm sitting out, because the 'Deal Me In' button is the same as the Fold button. i dont think theres anything i can do about that one

if you're getting it when no buttons are visible, i can only say to remove/re-include the site and make sure to get the fold button

I tried this with FTP and Im having problems with fold and stack.
After configuring for FTP, whenever I fold and stack, SaT will stack my table but it wont click the big fold button. Although it will highlight the small fold square if its present.

Currently using TN as a work around to fold, and Im sure the fold button was present when I pressed F10 for folding during site configuration.

any suggestions?

veryvery weird. so if its not your turn to act yet, fold+stack will click the fold preselect checkbox. but when it is your turn, it will not click the fold button?

i'm really at a loss, because all SaT does is click at a certain coordinate. obviously this click is working because it is clicking the checkbox. theres no real reason for it to not work once the other button appears.

heres a workaround to get fold and stack onto the same key, if you dont mind continuing to use TN.

use the same key in SaT for a 'Stack table' hotkey, but precede it with "~". so if you are using "F1" for fold in TN, then go to SaT and pick 'Stack table' for the action and type in "~F1" for the hotkey

let me know if that works

finding some more major bugs as i try to implement left click button detection

like forexample, during Include Site setup, it will grab the fold button color on PokerStars. so SaT searches for that color and determines if the table needs action. however, on stars, when you hover over the button, the button highlights and the button color changes, potentially throwing off the detection

It is not quite the same as the fold button. It is the bigbutton_off.svg.

I altered the color of that, and problem solved!

hrmm, didnt know about those graphics files. i cant seem to open .svg, but i could open the .png

how do you know that bigbutton is not used for all of Fold, Call, Bet, Deal Me In, Post Blind, etc?

fold call bet raise is smallbutton_off

http://www.inkscape.org/download/

thanks. are these bigbutton, smallbutton stuff documented somewhere?

not sure what you mean. Maybe the Full Tilt Poker Mods Thread?

what does SaT scan to detect if my table needs a VPIP action? is it scanning for the big fold/check/raise buttons? And is this the function used to move tables to grids for tile setting "preflop"?

Is there a way to automatically transfer all new tables to the stack slot?

it checks a few things, but most importantly if the Fold button is visible (which was grabbed during Include Site setup)

no, not at the moment. if you dont like the tables going to the New Tables stack when you press Start, you can always just turn off the New Tables stack by setting it to slot0. but perhaps there should be some way for this.

or, do you mean, that you arent using New Tables stack, and when you are playing normally and open a new table, you want it automatically to go into the main stack?

This would be good. Because Im trying out the preflop settings but sometimes the new tables will overlap with the running tables if "new tables stack" is 0. Or worse the new tables pop up over the stack and I wont notice it .

So it would be great if new tables can be immediately activated and transferred to the stack. For now Ill just use new tables stack.

And for the stack is it normal for the tables to keep on cycling until a table with fold button pops up? The cycling part hurts my eyes hehehe.

hi. Does this program take screen grabs of my tables at any time? The program I am running it in does not allow for any program to take screen grabs of my monitor, and that might account for the problems I aam having.

When i set up grid or try to add a site, it will NOT recognize a PS or FTP table. It allows me to set the ahk "stack and tile" window as my "poker table" but it will not recognize the actual PS or FTP table as being a window.

Am I doing something wrong that you can think of?

Also, why does this program connect to the internet on startup? Thanks.

Yeah, pretty much if new tables were immediately activated into the existing stack this program would be perfect.

hello,

one short question: the tool ist freeware right? what das the date on the webpage means? something with 15th august?!

is the tool stacking automatically, so no matter on pokerstars layout for example?

regarding new table stack and stack; is it alright if just 10-20% of the table is seen on my screen? Im doing it to save space, and not to get annoyed with the stack and new table stacks flickering.

Or does SaT need to see the whole table on my screen?
Image will show 10 slots on my 2 LCDs, where slots 9 and 10(stack and new table stack) are beside slots 2 and 4.



@nomar2408: its still in beta so its free.

quick question, can please anyone help? i am using windows 7 and am trying to setup up grid. but nothing happends if i am pressing f10. i tried also checkbox alternat pixel win7.

every other window like browser or stackandtile itself is recognize as a window. what should i do?

have you selected a poker table as the standard size for the grid before pressing F10?

tested this, the new table stack will detect new tables and tables can be transferred to the stack BUT once the table leaves the stack "fold and stack" wont work.

Also when I transferred the stack slot, SaT can transfer a table to the old stack grid, so I dont understand why it doesnt work for "fold and stack".

try running the program as an admin

that was the problem. thanks!